The Importance of Grounding a Radionic Instrument

Something that’s very important that many books on radionics fail to mention, or they only devote a short paragraph to is grounding your radionic instrument. It is important to ground your radionic instrument for two reasons.

1 Grounding your instrument will cut down on broadcast times, also grounding is essential if you are using your instruments to balance crops, trees, plants etc.

   2 There is evidence that if your instrument isn’t grounded, and you use it to do a lot of radionic balancing on other people, animals, etc. the conditions that are affecting them could be broadcast back to you, and cause you health problems. I have no proof of this, but some of the worlds most prominent radionic experts died at a fairly young age among them David Tansley, Peter Moscow,  Pat Schmidt, you would think with their extensive knowledge of radionics they could have prolonged their lives into old age. Maybe the problem was that they didn’t ground their instruments.  I figure for the time it takes, and the cost of a grounding rod and a piece of wire and a few jacks it’s better to be safe than sorry.

  If you have a Hieronymus type instrument grounding the instrument is easy. On these instruments, there is usually a place to plug-in a ground wire. All you have to do is to drive a metal rod into the ground ( I used a copper pipe).The longer the rod the better, but 3 or 4 feet should be long enough.  Attach the ground wire to the rod (this can be ordinary copper wire, insulated or bare, size or gauge doesn’t matter). Now install a Banana Plug ( available at any electronics supply store) on the end of the wire and plug the Banana Plug into your radionics instrument ( Most radionics instruments that are meant to be grounded have a jack for a Banana Plug. Plug the Banana Plug into the “input side” of the instrument) and you’re good to go. Some people recommend giving the wire a counter-clockwise twist to eliminate any natural polarity of the wire. You can do this with an electric drill set on reverse. You can ground as many instruments as you want using the same ground rod.


250301                                                                               Banana Plugs

  The above instructions are fine if you live in your own home, or are renting and your landlord doesn’t mind if you construct the above set-up.  Some people choose to ground their instruments to water pipes, gas lines or electrical grounds. Water pipes and gas lines are better than electrical grounds ( electrical grounds contain a lot of electrical noise and information). None of the above is as good as a dedicated ground rod for your instrument. An exception would be if you have a private well, you could use the well pipes as a  ground providing they are metal, they would be almost as good as the ground rod.

  If you are not sure if something will make a good ground dowse the question with your radionic instrument, if Yes use it, if No, find a better ground.

  But what if you live in an apartment building and the landlord says NO to you setting up a ground rod and wire, or you move your radionic instrument around often to different locations, where grounding to a permanent grounding rod wouldn’t be practical or have a radionic instrument that doesn’t provide for grounding such as the SE-5 computerized radionics instrument. There is another option.

  Another option is the “Virtual Ground” invented by Scott Ertl, he can be contacted here :Scott Ertl, 7775 U.S. Highway 10, Marshfield, Wis. 54449 (ph 715 387-1687; ertlacresgmx I have never used this but have heard good reports about it from other radionic operators.

  Some people put a tensor ring around the instrument, such as this one.


Other people place a crystal on the stick pad

The acid test is before you start balancing anyone or anything besides yourself dowse the question ” Is this radionic broadcast effecting me in any way” you answer should always be “No”

  If you plan on doing radionic work on anyone or anything but yourself, for your own sake ( not to mention it will cut down on broadcast times) please ground your instrument.

14 thoughts on “The Importance of Grounding a Radionic Instrument

  1. Fact check: The early passing of my father, Peter J. Kelly, had nothing to do with the grounding of his instruments and everything to do with the facts that he spent the entirety of his adult life between 300-350 pounds, chain smoked, and got very little exercise. Besides that, he was quite scrupulous about the grounding of his instruments, which is why they have always had “ground” marked clearly on every unit from the earliest models in the 1970s until today.


    1. Thanks for clearing that up Ed. Using an ungrounded radionic instrument was not the cause of your dad’s passing. Although there has been speculation that using ungrounded instruments have led to other radionic practitioners becoming ill and dying. I guess it’s better to ground and instrument, and be safe than sorry.


  2. And I thought “no I don’t need to ground my device, it is all about intention” … WRONG!
    I build a new prototype and forgot somehow to ground it and the remedy I broadcast came back to me. GRRRRR … Now I know better. Thanks for this post!


  3. Good question Pablo, I haven’t built a Radionics machine, so I’m not sure where you would connect the ground inside the machine.. After the machine is built the best ground is from a steel rod or pipe driven in the ground, with a wire running between that and your machine. If you join this radionics group on Facebook, I’m sure someone there could answer your question better than I could.


    1. what youwould do would be run a ground wire out of a window and down to the ground and attach to a ground rod in the dirt. Even better is out through the wall. This is probably not doable in an apartment. A virtual ground unit is the next best option. You could also set your instrument inside a tensor ring. If you don’t know what that is then visit


Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s